Bar stock or plate: the yield decision that sets your part price
Start with the two shapes
A turned part is a solid of revolution. A milled part is a prism. The material cost of each is set by how much of the bought stock ends up in the finished part - the yield - and the buy price per kilogram of that stock form.
| Stock form | Typical buy price | Yield on a round part | Yield on a flat part | Notes |
|---|---|---|---|---|
| Round bar | Reference | 70-85% | 20-40% (wasteful) | Cheap, fast, available in most grades |
| Plate | Reference +5-15% | 20-40% (wasteful) | 50-75% | Needs flattening stress relief on thin plate |
| Tube | +20-40% | n/a | n/a | For hollow parts, big saving on bore material |
| Near-net forging | +30-60% | 80-90% | 80-90% | Only economic above a few thousand pieces |
| Cast billet | +10-30% | 60-80% | 60-80% | Porosity risk; needs X-ray on critical parts |
The percentages assume sensible nesting. Poor nesting on plate - laying parts out without rotating them - can waste another 15% on its own.
Worked example: a Ø18 × 25 mm flange with a Ø8 bore
From Ø20 bar. Blank length 27 mm. Bar volume = π × 10² × 27 = 8,482 mm³. Part volume = π × 9² × 25 − π × 4² × 25 = 6,362 − 1,257 = 5,105 mm³. Yield = 60%. The machine has to turn the OD from Ø20 to Ø18 and face both ends - a short cycle on a lathe.
From 20 mm plate. A 22 × 22 mm square blank per part (allowing for the saw kerf) = 9,680 mm³. Yield = 53%. Better than bar - but now the part needs to be milled: face both sides, mill the OD round (or turn it if the shop has a mill-turn), bore the centre. Cycle time is 3-6 times the bar route.
So bar wins here, on cycle time, even though the yield is only slightly better. That is the usual outcome for round parts under Ø60 mm. The reversal happens when the part is large and flat: a 300 × 200 × 12 mm cover plate from Ø320 bar would need a 320 mm billet and turn 90% of it into chips.
When plate wins
- Large flat parts where bar would have to be turned down: covers, brackets, base plates.
- Parts with a large pocket - a pocket removes material either way, but from plate the removal is milling, and milling is where the machine is already set up.
- Multiple parts nested - three brackets nested in one plate blank can beat three individual bar cuts.
- Thin parts where bowing matters - plate can be stress-relieved before machining; bar releases stress differently.
When bar wins
- Anything with rotational symmetry under Ø60-80 mm: turned parts are the cheapest geometry in machining.
- Long, slender parts - bar plus a Swiss lathe with a guide bushing is the only economic route.
- Small quantities - bar is stocked, plate may need a cut-to-size order with a minimum.
- Tight concentricity - one turning operation holds bore-to-OD relation better than milling plus boring.
The question to ask a supplier
"What stock form are you quoting, and what is the yield?" is a better question than "what is the material cost". The second invites a number; the first invites a route, and the route determines whether the number makes sense.
A related question: is the material cut from remnant stock or ordered for this job? Remnant is cheaper and available now, but may not have a traceable heat number. For parts that need certification, that matters.
One more thing: stress
Plate carries internal stress from rolling. Machine one face and it bows. The usual answer is to machine both faces in stages, or to stress-relieve the blank first. Bar carries stress differently - it tends to move when you remove the outer layer, which is why thin-walled turned parts sometimes go oval after the last pass.
Neither is a defect; both are predictable. The point is that the stock form decision is part of the process planning, not a purchasing detail.
A second example where plate wins
A 180 × 120 × 16 mm mounting bracket with a 120 × 70 mm through pocket. From plate: blank 184 × 124 mm, yield around 58% before the pocket, and the pocket is removed by milling - a process the part already needs. From Ø220 bar: the blank weighs about 2.9 times the finished part, and the turning operation would remove material from all four sides of what is fundamentally a rectangular part.
| From plate | From bar | |
|---|---|---|
| Blank mass, kg | 1.36 | 4.02 |
| Yield | ~48% (with pocket) | ~16% |
| Operations | Mill 3 faces, pocket, drill | Turn to rectangle (wasteful), then mill |
| Cycle time index | 1.0 | 3.4 |
| Sensible? | Yes | No |
The rule that falls out of both examples: the part's dominant geometry picks the stock form. If most of the material removal is rotational, use bar. If it is planar, use plate. When a part is both - a round boss on a rectangular base - the shop has to pick one and eat the inefficiency, and that choice shows up in the price.
What to ask, in one sentence
"What stock form are you quoting, and what is the yield?" The answer tells you whether the price is a route or a guess.
Tube: the option people forget
For a hollow part - a bushing, a sleeve, a connector shell - tube can beat both bar and plate because the bore is already there. A Ø30 outside / Ø22 inside sleeve from Ø32 bar means turning 22 mm of solid material into chips; from 30 × 4 mm tube it means a light cleanup pass.
| Stock | Material used | Machining | Sensible when |
|---|---|---|---|
| Ø32 solid bar | High - the bore becomes chips | Bore + turn OD | No tube in that size or wall |
| 30 × 4 mm tube | Low | Turn OD, face, light bore cleanup | Wall thickness suits the finished part |
| Plate + boring | Medium | Mill round, then bore | Small quantity, tube not stocked |
The catch: tube has a seam or is seamless, and wall thickness tolerance is looser than a machined bore. If the inside diameter carries a tolerance tighter than about ±0.1 mm, you will bore it anyway - which removes most of the saving. Tube pays when the bore tolerance is loose and the wall is thin.
Questions buyers ask
Is plate more expensive than bar?
Usually 5-15% more per kilogram for the same alloy, and it often needs a cut-to-size order. The advantage is yield on flat parts, which can more than offset the price difference.
Can you machine a round part from plate?
Yes - mill it round, or turn it on a mill-turn. It is done when plate stock is on hand and bar would need ordering. The cycle time is higher, so it is normally limited to small quantities or large diameters.
What is near-net forging and when does it pay?
A forging shaped close to the finished part, so little material has to be removed. It pays above a few thousand pieces or when the material is expensive (titanium, Inconel), but it adds tooling cost and lead time.
Does the stock form affect the tolerance I can hold?
It affects stability more than accuracy. Plate can bow after machining; bar can relax when turned thin. Both are handled by process sequencing, not by tighter machines.
Our turning and milling lines are separate on purpose, so the stock-form route is chosen by the part, not by capacity.
equipment list