CHX Precision Metal

What a first-article report should contain

Updated 2026-11-15 · CHX Precision Metal

A usable first-article report has six parts: every dimension with nominal, limits and measured value; material certification with heat number; heat treat and finishing records; GD&T results stated against datums; cosmetic and functional checks; and a signature tied to the order and lot number. Missing any one of them reduces it to a certificate you cannot act on.

Why the first article is different from any other inspection

The first article is the only point where the whole process is proven at once: programme, tooling, fixture, gauges and material all meet for the first time. If it passes, the route is capable. If it fails, the route changes - and you want to know that before 500 parts are made, not after.

That is also why "we checked the first one, it was fine" is not a substitute for a report. Verbal confirmation cannot be audited and cannot be compared to the next run.

The six sections

1. Dimensioned results

2. Material certificate

Check three things: the grade and temper match the drawing, the heat number matches the material actually drawn from stock, and the chemistry plus mechanical properties are on the certificate. A mill cert whose heat number cannot be traced to the lot is decoration.

3. Heat treat and finishing records

Heat treat: process, hardness measured values, furnace or batch reference. Finishing: type, coating thickness, colour reference, sealing method. Subcontracted operations must carry the subcontractor's own record - not a line saying "finished".

4. GD&T data with datums

Every geometric result must name its datum. "Concentricity 0.008" without stating the axis it is measured against cannot be evaluated. Also look for the measurement temperature; on precision work, a report without one is worth less.

5. Cosmetic and functional checks

Cosmetic: judged against a signed sample, a written description (scratch length, count, location) or a colour reference with a ΔE allowance. Functional: go/no-go, thread gauging, leak test, fit check. "Visual OK" is not a result.

6. Sign-off tied to the lot

Inspector name, date, report number, purchase order number, lot number. Without the lot tie, the report does not prove anything about the box in front of you.

Four reports that look complete but are not

TypeHow to spot itWhy it fails
Caliper-only reportEvery value has two decimalsCannot support ±0.005 or any GD&T
No balloon numbers"Diameter 10.00" with no drawing referenceCannot tell which feature was measured
Empty datum columnGD&T values without datum lettersConclusion is undefined
"OK" instead of valuesMeasured column reads OK / PASSNo data, so no evidence

Reading one in two minutes

  1. Start at the end: signature, date, PO number, lot number. Confirm it is your lot.
  2. Go to the critical dimensions and check the measured values, not the pass column.
  3. Check the datum letters on every GD&T line.
  4. Scan the remaining rows for blanks and for values sitting exactly on a limit (which usually means rounding).
  5. Check that the material heat number matches the packing list or the material tag.

What comes after the first article

The first article proves the start; process records prove the run. For a batch order, ask additionally for: in-process inspection frequency and results, tool change records on precision work, and a final inspection report. Those three make the difference between "it was right once" and "it was right throughout".

A sample line, and what makes it good

Here is one row from a report that would pass review:

BalloonFeatureNominalLimitsMeasuredResult
17Bore Ø8.0007.985 / 8.0157.998Pass
18Position ⌖ Ø0.2 A B C0.200max 0.2000.084Pass
19Surface Ra0.8max 0.80.62Pass

Three things make this usable: the balloon number ties to the drawing, the limits are explicit (not just the nominal), and the GD&T line names its datums. A report where the position row reads "OK" instead of 0.084 has no evidence behind it - you cannot tell whether the inspector measured or assumed.

How a first article is actually produced

  1. The process engineer balloons the drawing and issues a measurement plan.
  2. The part is machined; the operator checks the easy dimensions in-process.
  3. The part sits in the inspection room until it reaches 20 °C (2 hours minimum for steel).
  4. CMM programme runs; hard-to-reach features are measured on a height gauge or profile projector.
  5. Values are entered against the balloon numbers; any dimension outside limits goes to the engineer before the report is issued.
  6. The report is signed and, if the part passes, batch production is released.

The step buyers never see is number five. A shop that has this loop will often report a failure and re-cut the part before shipping anything - which is why a first article arriving with all values in the middle of the tolerance band is normal, not suspicious.

What to do with a report that fails

A failing first article is often more informative than a passing one, because it shows where the process margin is thin. Ask for the measured value against the limit, the cause, and the corrective action. If the answer is "we will adjust the offset and re-measure", that is a valid action provided the root cause is understood - an offset adjustment that masks a fixture problem will come back at piece 200.

Questions buyers ask

Is a first-article report the same as a full dimensional report?

Not quite. A full dimensional report covers dimensions only. A first-article report also covers material, processes, cosmetics and function, and usually includes the dimensional data as one section.

Do I need an FAI on a prototype?

Yes. A prototype is the extreme case of a first article. Without data, the only proof is whether it fits - and by then the geometry has already been accepted.

Can the report be produced after shipment?

The format can be re-issued; the data cannot be re-created. If the report is dated after the shipment date, ask when the measurement was actually taken.

What is the difference between FAI and PPAP?

FAI covers one part against the drawing. PPAP is a production-part approval package covering process capability, control plans and MSA as well. For general machining, FAI is normally enough; automotive customers may require PPAP.

Every lot ships with a CMM-measured first-article report; the inspection scope is on the quality page.

quality and inspection