Mill certificates and heat numbers: what traceability proves
Three certificate types, three levels of evidence
| Type | What it is | Who signs it | What it proves |
|---|---|---|---|
| EN 10204 2.2 | Declaration of compliance with the order | Seller, not independent | The seller says the material meets the spec |
| EN 10204 3.1 | Inspection certificate, specific test results | Mill's authorised inspection rep | Chemistry and mechanical results from the actual heat |
| EN 10204 3.2 | Inspection certificate with third-party witness | Mill plus independent inspector | Same as 3.1, witnessed by a third party |
For most industrial buyers, 3.1 is the standard ask. 2.2 is common for commodity grades and tells you much less - it is a statement, not data. 3.2 is for pressure, nuclear and similar scopes, and adds cost and lead time.
The chain that has to hold
- Purchase record - the mill or stockholder invoice, with heat number and quantity.
- Warehouse label - the bundle or bar end marked with the heat number when it is received.
- Job traveller - the heat number copied onto the work order that consumes that bar.
- Inspection report - the same heat number on the certificate that ships with the parts.
Break any link and the certificate becomes an assertion about a different piece of metal. The usual break is at the warehouse: bars go into a rack, labels fall off, and the next job takes "some 6061" from the rack. A shop with a real traceability process marks the bar end and keeps remnants with their heat numbers.
Where substitution actually happens
| Substitution | Why it happens | What it costs the buyer |
|---|---|---|
| 6063 instead of 6061 | Cheaper, machines faster, often in stock | Lower strength (T5 vs T6); anodises slightly differently |
| 303 instead of 304 | Free-machining grade, much faster on a lathe | Lower corrosion resistance; not for food or medical |
| 304 instead of 316L | Availability, price | Chloride pitting; fails in marine or chemical service |
| Chinese grade "equivalent" | Mill uses its own designation | Chemistry within spec or not - only the 3.1 certificate tells you |
| Remnant bar of unknown heat | Convenience | No traceability at all |
None of these are necessarily dishonest. 6063 is a legitimate alloy; the problem is a drawing that says 6061-T6 and a part made from 6063-T5. The buyer finds out at anodising, or at the strength test, or never.
How to make the certificate useful
- Put the certificate requirement on the drawing or the PO: EN 10204 3.1, heat number to be stated on the inspection report.
- Ask for the heat number on the packing list, not only in the certificate PDF.
- For critical parts, ask for the bar-end marking to be photographed before cutting.
- Check the chemistry columns against the grade spec - not just the grade name printed at the top.
- On repeat orders, compare heat numbers between lots; the same heat number on two orders a year apart is a warning sign.
Independent verification
If the material is critical and the paperwork is thin, a hand-held XRF analyser gives a rapid alloy check - it will separate 304 from 316 and 6061 from 6063 in seconds, in the receiving area. It will not give mechanical properties or a full chemistry, but it catches the substitution that matters most.
For full confirmation, a coupon from the same bar can go to a laboratory for chemistry and tensile testing. That costs more than the certificate and takes a week, which is why it is reserved for the parts where a material failure is not survivable.
What a certificate does not tell you
- It does not tell you the condition of the bar when it was cut - rust, handling damage, or a bend from storage.
- It does not tell you whether the part was machined from that bar. Only the job traveller and the bar-end marking do.
- It does not guarantee the mechanical properties after machining - cold work, heat from aggressive cutting and weld repair all change the local condition.
- It does not cover the plating or coating, which has its own certificate and its own thickness measurement.
Lot splitting, and why it matters at receiving
A 2,000-piece order may be produced from three different bars, therefore three heat numbers. If the inspection report quotes one heat number, either the order was made from one bar - possible for small parts - or the report is only valid for part of the lot.
The practical check: on a lot above a few hundred pieces, ask how many heat numbers are involved and whether the packing list records which cartons came from which. A shop that can answer this in one sentence has real traceability; a shop that has to go and ask someone does not.
Receiving checklist for material documentation
| Check | Pass condition | Common failure |
|---|---|---|
| Certificate type | 3.1 with test results | 2.2 statement only |
| Heat number present | On certificate and packing list | Only on the certificate |
| Chemistry vs grade | Within spec for each element | Grade name correct, chemistry from a different grade |
| Condition / temper | T6, T651, annealed - stated | Silent on temper |
| Quantity traceable | Heat numbers mapped to cartons | One heat number quoted for a multi-bar lot |
Run this list against the first delivery, not the tenth. A supplier whose documentation passes on the first lot will usually keep passing; one whose documentation is assembled afterwards will show it immediately, and it is much cheaper to find that out before the parts are in a machine.
Questions buyers ask
Is a mill certificate the same as a material certificate?
Usually used interchangeably, but the certificate is only the document. What matters is whether it carries specific test results (3.1) or only a statement of compliance (2.2).
What if the supplier cannot provide a heat number?
Then the material is untraceable. For non-critical parts that may be acceptable; for anything with a strength, corrosion or regulatory requirement, it should disqualify the lot.
Does 6061 vs 6063 matter for anodising?
Yes. 6063 anodises to a slightly brighter, more uniform finish and is common for architectural work; 6061 is stronger and takes dye a little differently. Mixing them in one batch produces visible colour variation.
Can XRF replace a mill certificate?
No. XRF confirms the alloy family, not the heat treatment, mechanical properties or the full chemistry. It is a screening tool for substitution, not a substitute for documentation.
Do small orders need a 3.1 certificate?
If the part has a strength or corrosion requirement, yes - the cost is usually a small document fee. For brackets and covers where any 6061 will do, 2.2 plus an XRF check is often enough.
Material certificates ship with the inspection report, heat number matched to the lot.
quality and inspection